Difference between revisions of "PPPoE"

From Funtoo
Jump to: navigation, search
Line 14: Line 14:
 
CONFIG_PPP_SYNC_TTY=m</pre>
 
CONFIG_PPP_SYNC_TTY=m</pre>
 
Install and configure <code>rp-pppoe</code>.
 
Install and configure <code>rp-pppoe</code>.
<pre># emerge rp-pppoe
+
<console># ##i##emerge rp-pppoe
# pppoe-setup</pre>
+
# ##i##pppoe-setup
 +
</console>
 
Configuration is straightforward, setup username, password and ethernet interface to use, in our example it is <code>eth2</code>.
 
Configuration is straightforward, setup username, password and ethernet interface to use, in our example it is <code>eth2</code>.
 
= Funtoo Linux network setup =
 
= Funtoo Linux network setup =
 
Funtoo openrc does not provide default template for ppp connections. We will create a custom template.
 
Funtoo openrc does not provide default template for ppp connections. We will create a custom template.
<pre># cd /etc/netif.d/</pre>
+
<console># ##i##cd /etc/netif.d/</console>
 
Create <code>interface-pppoe</code>
 
Create <code>interface-pppoe</code>
 
<pre>#!/bin/sh
 
<pre>#!/bin/sh
Line 29: Line 30:
 
}</pre>
 
}</pre>
 
Now we will create a <code>eth2</code> interface as follows:
 
Now we will create a <code>eth2</code> interface as follows:
<pre># cd /etc/init.d
+
<console># ##i##cd /etc/init.d
# ln -s netif.tmpl netif.eth2</pre>
+
# ##i##ln -s netif.tmpl netif.eth2</console>
 
Then create an <code>/etc/conf.d/netif.eth2</code> configuration file that would specify a pppoe template in <code>/etc/netif.d</code> directory:
 
Then create an <code>/etc/conf.d/netif.eth2</code> configuration file that would specify a pppoe template in <code>/etc/netif.d</code> directory:
 
<pre>template="interface-pppoe"
 
<pre>template="interface-pppoe"
 
description="Your ISP"</pre>
 
description="Your ISP"</pre>
 
To complete configuration add an interface to default runlevel:
 
To complete configuration add an interface to default runlevel:
<pre> # rc-update add netif.eth2 default</pre>
+
<console> # ##i##rc-update add netif.eth2 default</console>
  
 
[[Category:Networking]]
 
[[Category:Networking]]
 
[[Category:HOWTO]]
 
[[Category:HOWTO]]

Revision as of 19:11, 11 January 2014

This page expains how to setup and configue PPPoE connection with rp-pppoe and Funtoo Linux network.

Kernel options

Make sure following kernel options are enabled

# zgrep PPP /proc/config.gz
CONFIG_PPP=m
CONFIG_PPP_BSDCOMP=m
# CONFIG_PPP_DEFLATE is not set
CONFIG_PPP_FILTER=y
CONFIG_PPP_MPPE=m
CONFIG_PPP_MULTILINK=y
CONFIG_PPPOE=m
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m

Install and configure rp-pppoe.

# emerge rp-pppoe
# pppoe-setup

Configuration is straightforward, setup username, password and ethernet interface to use, in our example it is eth2.

Funtoo Linux network setup

Funtoo openrc does not provide default template for ppp connections. We will create a custom template.

# cd /etc/netif.d/

Create interface-pppoe

#!/bin/sh
netif_pre_up() {
pppoe-connect >/var/log/pppoe.log 2>&1 &
}
netif_pre_down() {
pppoe-stop
}

Now we will create a eth2 interface as follows:

# cd /etc/init.d
# ln -s netif.tmpl netif.eth2

Then create an /etc/conf.d/netif.eth2 configuration file that would specify a pppoe template in /etc/netif.d directory:

template="interface-pppoe"
description="Your ISP"

To complete configuration add an interface to default runlevel:

 # rc-update add netif.eth2 default