Difference between revisions of "Install/GPT Partitioning"

From Funtoo
Jump to navigation Jump to search
(Marked this version for translation)
m (Suggest users skip UEFI section if they are not using it.)
(2 intermediate revisions by 2 users not shown)
Line 2: Line 2:
<includeonly>
<includeonly>
== GPT Partitioning == <!--T:1-->
== GPT Partitioning == <!--T:1-->
</includeonly><noinclude>
</includeonly><noinclude><languages/>
= Install Guide: GPT Partitioning =
= Install Guide: GPT Partitioning =


Line 11: Line 11:


<!--T:3-->
<!--T:3-->
{{Note|Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section, or reboot SystemRescueCD in UEFI mode first.}}
{{Note|Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot SystemRescueCD in UEFI mode first.}}


<!--T:4-->
<!--T:4-->
Line 88: Line 88:
{{Tip|You can verify that the block devices above were correctly created by running the command {{c|lsblk}}.}}
{{Tip|You can verify that the block devices above were correctly created by running the command {{c|lsblk}}.}}
</translate>
</translate>
<noinclude>{{InstallNavigation|num=4|prev=MBR Partitioning|next=Creating Filesystems|align=right}}</noinclude>

Revision as of 16:13, September 22, 2019

Other languages:
English • ‎español • ‎polski • ‎português do Brasil • ‎русский • ‎中文(中国大陆)‎

Install Guide: GPT Partitioning

Install Guide, Chapter 4 < Prev Next >

UEFI/GPT Method

   Note

Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot SystemRescueCD in UEFI mode first.

The gdisk commands to create a GPT partition table are as follows. Adapt sizes as necessary, although these defaults will work for most users. Start gdisk:

root # gdisk /dev/sda

Within gdisk, follow these steps:

Create a new empty partition table (This will erase all data on the disk when saved):

Command: o ↵
This option deletes all partitions and creates a new protective MBR.
Proceed? (Y/N): y ↵

Create Partition 1 (boot):

Command: n ↵
Partition Number: 1 ↵
First sector: 
Last sector: +500M ↵
Hex Code: EF00 ↵

Create Partition 2 (swap):

Command: n ↵
Partition Number: 2 ↵
First sector: 
Last sector: +4G ↵
Hex Code: 8200 ↵

Create Partition 3 (root):

Command: n ↵
Partition Number: 3 ↵
First sector: 
Last sector:  (for rest of disk)
Hex Code: 

Along the way, you can type "p" and hit Enter to view your current partition table. If you make a mistake, you can type "d" to delete an existing partition that you created. When you are satisfied with your partition setup, type "w" to write your configuration to disk:

Write Partition Table To Disk:

Command: w ↵
Do you want to proceed? (Y/N): Y ↵

The partition table will now be written to the disk and gdisk will close.

Now, your GPT/GUID partitions have been created, and will show up as the following block devices under Linux:

  • /dev/sda1, which will be used to hold the /boot filesystem,
  • /dev/sda2, which will be used for swap space, and
  • /dev/sda3, which will hold your root filesystem.
   Tip

You can verify that the block devices above were correctly created by running the command lsblk.

Install Guide, Chapter 4 < Prev Next >