Difference between revisions of "Install/GPT Partitioning"

From Funtoo
Jump to navigation Jump to search
m (add drive labeling)
m (Protected "Install/GPT Partitioning": create a draft in your user space and open a bug to change this page ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite)))
 
(16 intermediate revisions by 3 users not shown)
Line 12: Line 12:
<!--T:3-->
<!--T:3-->
{{Note|Use this method if you are interested in booting using UEFI, and if your Funtoo LiveCD initial boot menu was black and white, or the system booted without a boot menu. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot LiveCD in UEFI mode first.}}
{{Note|Use this method if you are interested in booting using UEFI, and if your Funtoo LiveCD initial boot menu was black and white, or the system booted without a boot menu. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot LiveCD in UEFI mode first.}}
<!--T:20-->
{{Note|You can build legacy mode into your GPT partition table but it requires a BIOS Boot partition.  see [[Talk:Install/GPT_Partitioning]]}}


<!--T:4-->
<!--T:4-->
Line 62: Line 65:
Last sector: ##i##↵##!i## (for rest of disk)
Last sector: ##i##↵##!i## (for rest of disk)
Hex Code: ##i##↵
Hex Code: ##i##↵
}}
{{console|body=
Command: ##i##c ↵
Partition Number: ##i##1
Enter name: boot
Command: ##i##c ↵
Partition Number: ##i##2
Enter name: swap
Command: ##i##c ↵
Partition Number: ##i##3
Enter name: root
}}
}}



Latest revision as of 04:26, December 13, 2021

Other languages:
English • ‎español • ‎polski • ‎português do Brasil • ‎русский • ‎中文(中国大陆)‎

Install Guide: GPT Partitioning

Install Guide, Chapter 4 < Prev Next >

UEFI/GPT Method

   Note

Use this method if you are interested in booting using UEFI, and if your Funtoo LiveCD initial boot menu was black and white, or the system booted without a boot menu. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot LiveCD in UEFI mode first.

   Note

You can build legacy mode into your GPT partition table but it requires a BIOS Boot partition. see Talk:Install/GPT_Partitioning

The gdisk commands to create a GPT partition table are as follows. Adapt sizes as necessary, although these defaults will work for most users. Start gdisk:

root # gdisk /dev/sda

Within gdisk, follow these steps:

Create a new empty partition table (This will erase all data on the disk when saved):

Command: o ↵
This option deletes all partitions and creates a new protective MBR.
Proceed? (Y/N): y ↵

Create Partition 1 (boot):

Command: n ↵
Partition Number: 1 ↵
First sector: 
Last sector: +128M ↵
Hex Code: EF00 ↵

Create Partition 2 (swap):

Command: n ↵
Partition Number: 2 ↵
First sector: 
Last sector: +4G ↵
Hex Code: 8200 ↵

Create Partition 3 (root):

Command: n ↵
Partition Number: 3 ↵
First sector: 
Last sector:  (for rest of disk)
Hex Code: 

Along the way, you can type "p" and hit Enter to view your current partition table. If you make a mistake, you can type "d" to delete an existing partition that you created. When you are satisfied with your partition setup, type "w" to write your configuration to disk:

Write Partition Table To Disk:

Command: w ↵
Do you want to proceed? (Y/N): Y ↵

The partition table will now be written to the disk and gdisk will close.

Now, your GPT/GUID partitions have been created, and will show up as the following block devices under Linux:

  • /dev/sda1, which will be used to hold the /boot filesystem,
  • /dev/sda2, which will be used for swap space, and
  • /dev/sda3, which will hold your root filesystem.
   Tip

You can verify that the block devices above were correctly created by running the command lsblk.

Install Guide, Chapter 4 < Prev Next >