Difference between revisions of "Install/GPT Partitioning/es"

From Funtoo
Jump to navigation Jump to search
(Created page with "'''Escribir la Tabla de Particiones en el Disco''':")
(Created page with "Ahora, sus particiones GPT/GUID han sido creadas, y se mostrarán como los siguientes ''dispositivos de bloque'' bajo Linux:")
Line 62: Line 62:
The partition table will now be written to the disk and {{c|gdisk}} will close.
The partition table will now be written to the disk and {{c|gdisk}} will close.


Now, your GPT/GUID partitions have been created, and will show up as the following ''block devices'' under Linux:
Ahora, sus particiones GPT/GUID han sido creadas, y se mostrarán como los siguientes ''dispositivos de bloque'' bajo Linux:


* {{c|/dev/sda1}}, which will be used to hold the {{c|/boot}} filesystem,  
* {{c|/dev/sda1}}, which will be used to hold the {{c|/boot}} filesystem,  

Revision as of 19:49, October 11, 2018

Other languages:
English • ‎español • ‎polski • ‎português do Brasil • ‎русский • ‎中文(中国大陆)‎

Guia de instalacion : Particionado GPT

Install Guide, Chapter 4 < Prev Next >

Metodo UEFI/GPT

   Note

Utilice este método si está interesado en iniciar con UEFI, y si el menú de inicio de "System Rescue CD" fue blanco y negro. Si era azul claro, este método no funcionará. En su lugar, use las instrucciones de la sección anterior o reinicie "System Rescue CD" en modo UEFI primero.

Los comandos de gdisk para crear una tabla de particiones GPT son los siguientes. Adapte los tamaños según sea necesario, aunque estos valores predeterminados funcionarán para la mayoría de los usuarios. Inicie gdisk:

root # gdisk /dev/sda

Dentro de fdisk, sigue estos pasos:

Create a new empty partition table (This will erase all data on the disk when saved):

Command: o ↵
This option deletes all partitions and creates a new protective MBR.
Proceed? (Y/N): y ↵

Create Partition 1 (boot):

Command: n ↵
Partition Number: 1 ↵
First sector: 
Last sector: +500M ↵
Hex Code: EF00 ↵

Crear la Partición 2 (swap):

Command: n ↵
Partition Number: 2 ↵
First sector: 
Last sector: +4G ↵
Hex Code: 8200 ↵

Crear la Partición 3 (root):

Command: n ↵
Partition Number: 3 ↵
First sector: 
Last sector:  (for rest of disk)
Hex Code: 

Durante este proceso puede teclear "p" y presionar Enter para visualizar la tabla de particiones actual. Si comete algún error, puede teclear "d" para borrar una partición existente que fue creada previamente. Cuando esté satisfecho con las particiones creadas teclee "w" para grabar la configuración en el disco:

Escribir la Tabla de Particiones en el Disco:

Command: w ↵
Do you want to proceed? (Y/N): Y ↵

The partition table will now be written to the disk and gdisk will close.

Ahora, sus particiones GPT/GUID han sido creadas, y se mostrarán como los siguientes dispositivos de bloque bajo Linux:

  • /dev/sda1, which will be used to hold the /boot filesystem,
  • /dev/sda2, which will be used for swap space, and
  • /dev/sda3, which will hold your root filesystem.
   Tip

You can verify that the block devices above were correctly created by running the command lsblk.