Difference between revisions of "Install/MBR Partitioning/zh-tw"

From Funtoo
Jump to navigation Jump to search
(Created page with "{{console|body= Command (m for help): ##i##o ↵ }}")
Line 97: Line 97:


{{console|body=
{{console|body=
Command (m for help): ##i##o ↵
Command (m for help): ##i##p
}}


Disk /dev/sda: 298.1 GiB, 320072933376 bytes, 625142448 sectors
Disk /dev/sda: 298.1 GiB, 320072933376 bytes, 625142448 sectors

Revision as of 07:04, October 24, 2018

Other languages:
English • ‎español • ‎polski • ‎português do Brasil • ‎русский • ‎中文(中国大陆)‎ • ‎中文(台灣)‎

安裝教學 : MBR分割

Install Guide, Chapter 3 < Prev Next >

Legacy (BIOS/MBR) 方法

   Note

Use this method if you are booting using your BIOS, and if your System Rescue CD initial boot menu was light blue. If you're going to use the UEFI/GPT disk format, then please proceed to the next section.

首先,你需要找到正確的硬碟來進行分割,使用這個指令來確認/dev/sda是你要用來分割的硬碟。

root # fdisk -l /dev/sda

Disk /dev/sda: 640.1 GB, 640135028736 bytes, 1250263728 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: gpt

root #         Start          End    Size  Type            Name
 1         2048   1250263694  596.2G  Linux filesyste Linux filesystem

Now, it is recommended that you erase any existing MBR or GPT partition tables on the disk, which could confuse the system's BIOS at boot time. We accomplish this using sgdisk:

   Warning

This will make any existing partitions inaccessible! You are strongly cautioned and advised to backup any critical data before proceeding.

root # sgdisk --zap-all /dev/sda

Creating new GPT entries.
GPT data structures destroyed! You may now partition the disk using fdisk or
other utilities.

This output is also nothing to worry about, as the command still succeeded:

***************************************************************
Found invalid GPT and valid MBR; converting MBR to GPT format
in memory. 
***************************************************************

Now we will use fdisk to create the MBR partition table and partitions:

root # fdisk /dev/sda

fdisk中依照下列指示操作:

清空分割表:

Command (m for help): o ↵

建立分割區1: (boot)

Command (m for help): n ↵
Partition type (default p): 
Partition number (1-4, default 1): 
First sector: 
Last sector: +128M ↵

建立分割區2 (swap):

Command (m for help): n ↵
Partition type (default p): 
Partition number (2-4, default 2): 
First sector: 
Last sector: +2G ↵
Command (m for help): t ↵ 
Partition number (1,2, default 2): 
Hex code (type L to list all codes): 82 ↵

建立root分割區:

Command (m for help): n ↵
Partition type (default p): 
Partition number (3,4, default 3): 
First sector: 
Last sector: 

驗證分割表:

Command (m for help): p

Disk /dev/sda: 298.1 GiB, 320072933376 bytes, 625142448 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x82abc9a6

Device    Boot     Start       End    Blocks  Id System
/dev/sda1           2048    264191    131072  83 Linux
/dev/sda2         264192   4458495   2097152  82 Linux swap / Solaris
/dev/sda3        4458496 625142447 310341976  83 Linux

Write the partition table to disk:

Command (m for help): w

Your new MBR partition table will now be written to your system disk.

   Note

You're done with partitioning! Now, jump over to Creating filesystems.