Difference between revisions of "User talk:Pnoecker/Raspberry Pi 4"

From Funtoo
Jump to navigation Jump to search
(Blanked the page)
Tag: Blanking
Line 1: Line 1:
{{console|body=
###i## echo "media-libs/raspberrypi-userland-bin **" >> /etc/portage/package.accept_keywords
###i## echo "sys-boot/raspberrypi-firmware **" >> /etc/portage/package.accept_keywords
###i## echo "sys-kernel/raspberrypi-image **" >> /etc/portage/package.accept_keywords
###i## emerge raspberrypi-userland-bin raspberrypi-firmware raspberrypi-image
}}


cmdline.txt
console=serial0,115200 console=tty1 root=PARTUUID=467a3359-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait quiet splash plymouth.ignore-serial-consoles
console=serial0,115200 console=tty1 root=PARTUUID=467a3359-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait plymouth.ignore-serial-consoles
config.txt
dtparam=audio=on
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
arm_64bit=1
pi@raspberrypi:~ $ cat /boot/config.txt
# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2
[all]
#dtoverlay=vc4-fkms-v3d
# NOOBS Auto-generated Settings:
pi@raspberrypi:~ $ cat /boot/cmdline.txt
console=serial0,115200 console=tty1 root=/dev/mmcblk0p7 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
pi@raspberrypi:~ $ cat /boot/issue.txt
Raspberry Pi reference 2020-08-20
Generated using pi-gen, https://github.com/RPi-Distro/pi-gen, 9a3a10bf1019ebb2d59053564dc6b90068bad27d, stage5

Revision as of 09:59, November 14, 2020

Retrieved from "https://www.funtoo.org/index.php?title=User_talk:Pnoecker/Raspberry_Pi_4&oldid=34383"