Difference between revisions of "U-booting Funtoo on the TI AM335x X2 SBC-B2"

From Funtoo
Jump to navigation Jump to search
m (D4g33z moved page U-booting Funtoo to U-booting Funtoo on the TI AM335x X2 SBC-B2: This is highly specific to the a particular cpu + board architecture.)
(No difference)

Revision as of 20:22, February 17, 2017

Introduction

Installing Funtoo to a Raspberry Pi is fun, but there are a lot more boards out there. For example, the carrier boards that hold a DIMM mounted AM335x series cpu. To get this going, we need to use the U-Boot bootloader, some knowledge of device tree blobs, and a lot of patience.

For this article, we are using this board. You can read all about it here but the steps depicted here should get you a manufacturer supplied 4.1.8 kernel with a Funtoo stage3 running on it. Possibly.

   Note

When you pick a board, documentation is just as important as hardware features. Without it, you WILL be hunting down someone in Shenzhen to explain why the board refuses to boot (you forgot to ground C8, of course).

   Warning

This is kind of a ridiculous exercise, given the author's limited level and the wild idiosyncrasies of board programming, but it may be instructive. It helps me.

Making the Environment

Edit xcompile_variables to set XC_WORK, XC_LINUX_PREFIX, ARCH, CROSSDEV_TARGET, and STAGE3 variables to taste. For this board, we use:

  • CROSSDEV_TARGET="arm-linux-gnueabihf"
  • ARCH=arm
  • STAGE3=funtoo-current/arm-32bit/armv7a_neon_hardfp
  • STAGE3_CFLAGS="-O2 -pipe -march=armv7-a -mfpu=neon -mfloat-abi=hard"
  • STAGE3_NAME=stage3-latest.tar.xz
root # . xcompile_variables.sh
root # mkdir -p $CONFIGS $FIRMWARE $LINUX $UBOOTS $STAGE3S

Retrieve Sources

root # git clone https://github.com/zhengsjgoembed/335x-b4-uboot.git $XC_UBOOT
root # git clone https://github.com/zhengsjgoembed/335x-b4.git $XC_KERNEL_SRC
root # wget https://git.ti.com/ti-cm3-pm-firmware/amx3-cm3/blobs/7c6075f28d9fdd633175cdbd8dc287613ce92e5d/bin/am335x-pm-firmware.bin -O $XC_FIRMWARE/am335x-pm-firmware.bin
root # wget https://git.ti.com/ti-cm3-pm-firmware/amx3-cm3/blobs/7c6075f28d9fdd633175cdbd8dc287613ce92e5d/bin/am335x-pm-firmware.elf -O $XC_FIRMWARE/am335x-pm-firmware.elf

Crossdev

See Crossdev_Automation for info on how to get crossdev running on Funtoo.

root # crossdev -t $CROSSDEV_TARGET --gcc 4.9.3 -P -v
root # gcc-config -l
 [1] arm-linux-gnueabihf-4.9.3 *
 [2] arm-linux-gnueabihf-5.2.0
 [3] arm-linux-gnueabihf-5.3.0

 [4] armv6j-hardfloat-linux-gnueabi-4.8.4 *

 [5] armv7a-hardfloat-linux-gnueabi-4.8.4
...<lots of compilers>...

Kernel Building

root # . xcompile_variables
root # get_kernel_version
4.1.18
root # set_kernel_extraversion = -defconfig && . xcompile_variables.sh
root # get_kernel_version 
4.1.18-defconfig
root # cd $XC_KERNEL_SRC
root # alias make="make -j<N>"
root # cp am335x_b4_deconfig $XC_KERNEL_CONFIG
root # . xcompile_variables
Your current kernel configs for <XC_LINUX_PREFIX> type builds:
Use 4.1.18.kconf as config (y/n)? y
Setting XC_KERNEL_OLDCONFIG to /usr/src/fun_kernel/configs/<XC_LINUX_PREFIX>/4.1.18.kconf
root # cp XC_KERNEL_OLDCONFIG .config
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make zImage modules dtbs

U-Boot Building

Notice the use of O=$XC_LINUX_PREFIX to control output. Remove this directory if you need to clean for a rebuild. DTC is the device tree compiler location that permits the use of Device Tree Blobs, an absolutely essential tool for managing the wild forest of ARM processors and base boards. See this tutorial on the Device Tree.

root # cd $XC_UBOOT
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make mrproper
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make distclean
root # rm -r ./$XC_LINUX_PREFIX
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make O=$XC_LINUX_PREFIX am335x_evm_config
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make O=$XC_LINUX_PREFIX DTC=$XC_KERNEL_SRC/scripts/dtc/dtc

Setup Stage3

Follow the steps in http://funtoo.org/Crossdev_Automation#Stage3_Configuration but do not set up a software clock. Our board has a hardware clock.

Copy Over Kernel Files and Firmware

root # cd $XC_KERNEL_SRC
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- INSTALL_MOD_PATH=$XC_STAGE3S INSTALL_MOD_STRIP=1 make modules_install
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- INSTALL_FW_PATH=$XC_STAGE3S make firmware_install
root # cp $XC_FIRMWARE/* $XC_STAGE3S/lib/firmware
root # cp  arch/arm/boot/zImage  $XC_STAGE3S/boot
root # cp arch/arm/boot/dts/*.dtb $XC_STAGE3S/boot
root # rm $XC_STAGE3S/lib/modules/`get_kernel_release`/{build,source}

Copy Over U-Boot Files

root # cp $XC_UBOOT/$XC_LINUX_PREFIX/{MLO,u-boot.img} $XC_STAGE3S/boot

Install to the Board

Make an image.

root # dd if=/dev/zero of=/dev/<your_dev> bs=1024 count=1024
root # parted -s /dev/<your_dev> mklabel msdos
root # parted -s /dev/<your_dev> unit cyl mkpart primary fat32 -- 0 9
root # parted -s /dev/<your_dev> set 1 boot on
root # parted -s /dev/<your_dev> unit cyl mkpart primary ext2 -- 9 -2
root # mkfs.vfat -F 32 -n boot /dev/<your_dev>1
root # mkfs.ext4 -L rootfs /dev/<your_dev>2

Mount and Rsync.

root # mkdir -p /mnt/funtoo
root # mount /dev/<your_dev>2 /mnt/funtoo
root # mkdir -p /mnt/funtoo/boot
root # mount /dev/<your_dev>1 /mnt/funtoo/boot
root # rsync -avz --exclude "usr/portage/*" $XC_STAGE3S/{boot,bin,etc,home,lib,mnt,opt,root,run,sbin,srv,tmp,usr,var,dev} /mnt/funtoo
root # mkdir -p /mnt/funtoo/{proc,sys}
root # umount -R /mnt/funtoo

Reboot! Moment of truth: do you really know what you are doing?

   Tip

Once you get the board up and sshd running on it, then use rsync -e "ssh" $XC_STAGE3S/{boot,lib} <board_ip>:/ to do the kernel hacking. How long can you keep it up?