Search results

• Funtoo:Metro/Manual Setup
  == First stages build (local build) == ...generic {{f|pentium4}} stage3 as a seed stage, then here the first set of steps we'd perform:
  11 KB (1,738 words) - 22:24, October 10, 2022
• Video
  Individual driver pages cover specific setup steps for each driver. The general process is as follows: First determine which video card you have and which driver it requires.
  3 KB (464 words) - 11:26, May 12, 2022
• Upgrade Instructions/1.2-release
  ...through the process of upgrading your system from Funtoo Linux 1.0 to 1.2. First, please make sure that you have created a backup of your system. If you cho ...en system and dealing with fixing it or re-installing. While these install steps are fairly robust, we will
  11 KB (1,792 words) - 18:04, January 28, 2019
• 32-bit Chroot/en
  ...s forums post]. This page provides background for this decision as well as steps that can be used to provide 32-bit support without multilib, namely a 32-bi To achieve this you must first create the necessary directories inside of the 32-bit chroot folder. Later
  12 KB (1,786 words) - 07:52, April 13, 2020
• Zope HOWTO
  ...features in Zope. Five was merged into mainline Zope 2 in early 2010, and first appeared in Zope 2.8. ...ope.org/zope2/zdgbook/Products.html Chapter 5] covers the creation of your first product.
  9 KB (1,392 words) - 17:32, June 25, 2015
• Install/Chroot/en
  The {{c|fchroot}} command will take care of all necessary steps to enter into your new Funtoo Linux system, as well as clean up things when
  2 KB (346 words) - 00:59, May 26, 2023
• GPG Signatures
  ...t key retrieval to complete successfully. Once this is done, the following steps can be performed:}}
  3 KB (434 words) - 17:41, July 23, 2023
• Install/Download LiveCD/zh-tw
  For steps on setting up network access from the LiveCD, please see the {{LiveCD}} pag First ensure that {{c|sshd}} is running. You may need to start {{c|sshd}} as foll
  4 KB (444 words) - 01:56, May 26, 2023
• Installation Troubleshooting
  ...ve this problem, boot from the live CD again [[#boot failure|following the steps above]]. Then, from within the chroot, edit {{c|etc/boot.conf}} and add the
  2 KB (379 words) - 07:58, August 29, 2018
• Upgrade Instructions/1.3-release/en
  ...it}} or {{c|gnome-kit}}, perform the following steps to correct your tree. First, add the following to {{f|/etc/ego.conf}}: ...at has {{c|dev-lang/go}} installed, you will need to perform the following steps: {{c|emerge -C dev-lang/go; emerge dev-lang/go}}.}}
  5 KB (833 words) - 05:03, April 14, 2019
• Creating Your Own Overlay
  There are two ways to create an overlay that we'll cover. The first is to simply create a local overlay as follows (courtesy seemant, thanks!) ...ease see the following video. We will still need to perform some finishing steps to get the overlay ready for use, which we will cover below.
  5 KB (859 words) - 17:59, December 22, 2023
• F2FS Install Guide
  ...UEFI booting. The [[UEFI Install Guide]] has more information on this, and steps on how to determine if your system supports UEFI. To use this recommended boot method, first emerge <code>sys-boot/grub</code>. This will also cause <code>grub-2</code>
  18 KB (2,656 words) - 16:14, December 20, 2021
• Upgrade Instructions/1.3-release/zh-cn
  ...it}} or {{c|gnome-kit}}, perform the following steps to correct your tree. First, add the following to {{f|/etc/ego.conf}}: ...at has {{c|dev-lang/go}} installed, you will need to perform the following steps: {{c|emerge -C dev-lang/go; emerge dev-lang/go}}.}}
  5 KB (826 words) - 20:03, April 7, 2021
• Partitioning in Action, Part 2
  ...on a separate disk to enhance performance. Then, I'll walk you through the steps required to move both /tmp and /var to this new partition. ...troyed. For this reason, it's highly recommended that you take appropriate steps to back up all critical files before proceeding.}}
  6 KB (993 words) - 01:26, January 2, 2015
• Package:OpenVAS
  Start OpenvVas Scanner (Required for next steps):
  3 KB (358 words) - 16:54, December 8, 2015
• Install/BootLoader/en
  ...school) or UEFI (new-school). As of boot-update-1.7.2, now in Portage, the steps are very similar. First, emerge <code>boot-update</code>. This will also cause <code>grub-2</code>
  3 KB (394 words) - 04:26, July 14, 2015
• Install/BootLoader
  ...school) or UEFI (new-school). As of boot-update-1.7.2, now in Portage, the steps are very similar. First, emerge <code>boot-update</code>. This will also cause <code>grub-2</code>
  3 KB (394 words) - 20:33, July 16, 2015
• Install/Chroot
  The {{c|fchroot}} command will take care of all necessary steps to enter into your new Funtoo Linux system, as well as clean up things when
  2 KB (370 words) - 00:59, May 26, 2023
• 32-bit Chroot
  ...s forums post]. This page provides background for this decision as well as steps that can be used to provide 32-bit support without multilib, namely a 32-bi To achieve this you must first create the necessary directories inside of the 32-bit chroot folder. Later
  13 KB (1,914 words) - 07:52, April 13, 2020
• LXD/zh-cn
  ...use LXD on a laptop, you are likely using WiFi and NetworkManager, and the steps below will ''not'' work for you bridge setup. Please see [[LXD/Laptop Netwo The following steps will show you how to set up a basic LXD environment under Funtoo Linux. Thi
  15 KB (2,186 words) - 19:55, June 22, 2022

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)